Peel & Stick Marble-Look Floor Tiles

Made for practical updates

A new floor look without replacing the subfloor.

The square format is easy to measure, arrange, trim, and replace on a properly prepared indoor floor.

01

Self-adhesive

Peel the liner and place each tile directly on a clean, smooth floor.

02

Easy to plan

The 30 cm square format creates a predictable grid for layout and cutting.

03

Eleven patterns

Choose from geometric and marble-inspired designs identified by stable pattern codes.

04

Wipeable finish

For routine care, wipe gently and avoid standing water at seams.

Plan before peeling

Start from a straight reference line.

Dry-lay several tiles first. This shows how the pattern meets at each edge and helps avoid a narrow cut along the most visible wall.

01
Measure the full areaInclude alcoves, doorways, and a cutting allowance.
02
Check pattern directionRotate the tiles before installation until the layout looks consistent.
03
Install from the centerUse level reference lines and work outward in manageable sections.

Close detail of self-adhesive patterned floor tile

Thin renovation layer

A 1.5 mm decorative floor covering.

This is a lightweight self-adhesive plastic floor tile, not ceramic, stone, or rigid composite flooring.

01
Low-profile formatThe listed thickness is approximately 1.5 mm.
02
Printed decorative faceThe pattern provides the stone or geometric appearance.
03
Peel-and-stick backingAdhesion depends on a flat, clean, dry, firmly bonded substrate.

Eleven pattern options

Choose by pattern code.

Codes match the product selector and help keep purchasing, inventory, and reordering consistent.

Pattern 557-8ACode 557-8A

Pattern 7085Code 7085

Pattern 81014-1Code 81014-1

Pattern 81015-1Code 81015-1

Pattern 81017-2Code 81017-2

Pattern 81010-4Code 81010-4

Pattern 81021-1Code 81021-1

Pattern 81022-1Code 81022-1

Pattern 81036-1Code 81036-1

Pattern 81102-2Code 81102-2

Installation guide

Four steps to cleaner seams.

01
Clean and dryRemove wax, grease, moisture, loose coating, dust, and raised debris.
02
Mark the gridUse perpendicular reference lines to keep rows square.
03
Peel and placeAlign first, then lower the tile without stretching it.
04
Press firmlySmooth the full tile and pay special attention to corners and seams.

Product details

Everything at a glance.

Product type	Self-adhesive decorative plastic floor tile
Tile size	30 × 30 cm (11.8 × 11.8 in)
Thickness	Approximately 1.5 mm (0.06 in)
Coverage per tile	0.09 m² / 0.97 sq. ft.
Pack options	10, 20, 30, or 40 pieces
Pattern options	11 supplier-listed pattern codes
Installation	Self-adhesive peel-and-stick backing
Recommended substrate	Clean, dry, smooth, flat, firmly bonded indoor floor
Supplier-listed spaces	Bathroom area, living room, bedroom, and corridor
Installation service	Not included
Care	Wipe gently; avoid standing water and moisture entering seams

Pack delivery: Select the same pattern code for all packs used in one area. Order enough at one time where possible, as small color differences can occur between production batches.

Good to know

Questions, answered.

How many tiles should I order?

Each tile covers about 0.97 sq. ft. Use the calculator above, which adds 10% for trimming and then rounds up to an available 10-piece increment.

Can I install them over uneven flooring?

No. Texture, deep grout lines, loose flooring, cracks, grease, dust, or moisture may show through and reduce adhesion.

Are these ceramic or stone tiles?

No. They are lightweight self-adhesive plastic floor tiles with printed decorative patterns.

Can I mix pattern codes?

You can design a mixed layout, but each code is visually different. For a continuous floor, use the same code throughout.

Can I use them in wet areas?

The supplier lists bathroom use, but keep seams away from standing water and continuously wet zones. The substrate must remain dry and firmly bonded.

Your cart is empty

Your cart

Estimated total

Peel & Stick Marble-Look Floor Tiles