Peel & Stick Wood-Grain Floor Tiles

Made for practical updates

Wood warmth without a full floor replacement.

The square format is easy to measure, arrange, trim, and replace on a properly prepared indoor floor.

01

Self-adhesive

Peel the liner and place each tile directly on a clean, smooth floor.

02

Embossed grain

A pressed surface texture adds detail to the printed wood appearance.

03

Eight wood tones

Stable pattern codes make selection, inventory, and reordering easier.

04

Wipeable PVC

For routine care, wipe gently and avoid standing water at seams.

Plan before peeling

Let the grain run in one direction.

Dry-lay several tiles first. Aligning the printed grain consistently helps the square tiles read as a more continuous wood surface.

01
Measure the full areaInclude alcoves, doorways, and a cutting allowance.
02
Check grain directionRotate every tile before peeling so adjacent wood lines feel intentional.
03
Install from a reference lineKeep rows square and press each edge before moving forward.

Thin renovation layer

Embossed PVC in a 1.5 mm profile.

This is a lightweight self-adhesive PVC floor tile, not solid wood, laminate plank, or rigid composite flooring.

01
Low-profile formatThe listed thickness is approximately 1.5 mm.
02
Wood-grain embossingThe pressed face adds surface detail to the printed wood pattern.
03
Peel-and-stick backingAdhesion depends on a flat, clean, dry, firmly bonded substrate.

Eight wood-grain options

Choose by pattern code.

Codes match the product selector and help keep purchasing, inventory, and reordering consistent.

Wood Grain 0005-5Code 0005-5

Wood Grain 1001-5Code 1001-5

Wood Grain 1002-7Code 1002-7

Wood Grain 6046-1Code 6046-1

Wood Grain 6056-1Code 6056-1

Wood Grain 6061-4Code 6061-4

Wood Grain 81115-3Code 81115-3

Wood Grain 81117-2Code 81117-2

Installation guide

Four steps to cleaner seams.

01
Clean and dryRemove wax, grease, moisture, loose coating, dust, and raised debris.
02
Mark the gridUse perpendicular reference lines to keep rows square.
03
Peel and placeAlign the wood grain first, then lower the tile without stretching it.
04
Press firmlySmooth the full tile and pay special attention to corners and seams.

Product details

Everything at a glance.

Product type	Self-adhesive embossed wood-grain floor tile
Material	PVC
Tile size	30 × 30 cm (11.8 × 11.8 in)
Thickness	Approximately 1.5 mm (0.06 in)
Coverage per tile	0.09 m² / 0.97 sq. ft.
Pack options	10, 20, or 30 pieces
Pattern options	8 supplier-listed wood-grain pattern codes
Surface treatment	Embossed finish
Installation	Self-adhesive peel-and-stick backing
Recommended substrate	Clean, dry, smooth, flat, firmly bonded indoor floor
Supplier-listed spaces	Bathroom area, living room, bedroom, corridor, and other interior spaces
Installation service	Not included
Care	Wipe gently; avoid standing water and moisture entering seams

Pack delivery: Select the same pattern code for all packs used in one area. Order enough at one time where possible, as small color differences can occur between production batches.

Good to know

Questions, answered.

How many tiles should I order?

Each tile covers about 0.97 sq. ft. Use the calculator above, which adds 10% for trimming and rounds up to an available 10-piece increment.

Can I install them over uneven flooring?

No. Texture, deep grout lines, loose flooring, cracks, grease, dust, or moisture may show through and reduce adhesion.

Are these solid wood or laminate?

No. They are lightweight self-adhesive PVC tiles with a printed and embossed wood-grain face.

Can I mix pattern codes?

You can design a mixed layout, but each code is visually different. For a continuous floor, use the same code throughout.

Can I use them in wet areas?

The supplier lists bathroom use and describes the tiles as water- and moisture-resistant. Keep seams away from standing water and continuously wet zones, and keep the substrate dry.

Sepetiniz boş

Sepetiniz

Tahmini toplam

Peel & Stick Wood-Grain Floor Tiles